Errata - English

Change
The spectrum obtained from the Sample solution shows IR maxima in the regions of 3500–3200, 2950–2890, 1653–1633, and 1070–1000 cm^–1.
to:
The spectrum obtained from the sample preparation shows IR maxima in the regions of 3500–3200, 2950–2890, 1653–1633, and 1070–1000 cm^–1.

In Release Liner Peel Test: Change
The product fails the test if the mean peel force is outside the acceptable range determined during product development.
to:
The product fails the test if the overall mean peel force is outside the acceptable range determined during product development.

In Organic Impurities/Table 3/footnote c: Change
2-[(2-Amino-6-oxo-1,6-dihydro-9H-purin-9-yl)methoxy]-2-hydroxypropyl methyl-L-valinate hydrochloride.
to:
3-[(2-Amino-6-oxo-1,6-dihydropurin-9-yl)methoxy]-2-hydroxypropyl L-valinate hydrochloride.

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

In Analysis: Change
Results = (A_U/A_S) × C_S × D × (1/L) × V × 100
A_U = absorbance of the Sample solution
A_S = absorbance of the Standard solution
C_S = concentration of USP Prochlorperazine Maleate RS in the Standard solution
D = dilution factor for Sample solution, if needed
L = label claim (mg/Tablet)
V = volume of Medium, 500 mL
to:
Result = (A_U/A_S) × C_S × V × D × (M_r1/M_r2) × (1/L) × 100
A_U = absorbance of the Sample solution
A_S = absorbance of the Standard solution
C_S = concentration of USP Prochlorperazine Maleate RS in the Standard solution
V = volume of Medium, 500 mL
D = dilution factor for the Sample solution, if needed
M_r1 = molecular weight of prochlorperazine, 373.94
M_r2 = molecular weight of prochlorperazine maleate, 606.09
L = label claim (mg/Tablet)

In Leachable Arsenic/Analysis: Change
A 3.0-mL portion of the Sample solution meets the requirements in Arsenic 〈211〉, Procedures, Procedure.
to:
A 3.0-mL portion of the Sample solution meets the requirements in Arsenic 〈211〉, Procedures, Procedure 1.

In Acetic Acid in Peptides/Analysis: Change
C_SPA = concentration of potassium acetate in each of the Standard solutions (mg/mL)
to:
C_SPA = concentration of potassium acetate in each of the Standard solutions (µg/mL)
AND
In Ammonium/Analysis: Change
C_SAC = concentration of ammonium chloride in each of the Standard solutions (mg/mL)
to:
C_SAC = concentration of ammonium chloride in each of the Standard solutions (µg/mL)

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide, monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

Change
System suitability solution: 5 µg/mL each of USP Promethazine Hydrochloride RS and USP Promethazine Related Compound B RS from the Standard stock solution and System suitability stock solution, respectively
Standard solution: 5 µg/mL of USP Promethazine Hydrochloride RS from the Standard stock solution
Sensitivity solution: 0.25 µg/mL of USP Promethazine Hydrochloride RS from the Standard solution
to:
System suitability solution: 5 µg/mL each of USP Promethazine Hydrochloride RS and USP Promethazine Related Compound B RS from the Standard stock solution and System suitability stock solution, respectively, in Diluent
Standard solution: 5 µg/mL of USP Promethazine Hydrochloride RS from the Standard stock solution in Diluent
Sensitivity solution: 0.25 µg/mL of USP Promethazine Hydrochloride RS from the Standard solution in Diluent

In Limit of Naloxone Related Compound D: Delete
Sensitivity solution: 1.25 µg/mL of USP Naloxone Related Compound D RS in 0.1 N hydrochloric acid
AND
In System suitability/Samples: Delete
Sensitivity solution,
AND
In System suitability/Suitability requirements: Delete
Signal-to-noise ratio: NLT 10, Sensitivity solution

In Analysis: Change
Result = (r_U/r_S) × C_S × (1/F)
to:
Result = (r_U/r_S) × C_F × (1/F)
AND
Change
C_S = final concentration of USP Isoflurane Related Compound B RS in the Standard solution (%)
to:
C_F = final concentration of USP Isoflurane Related Compound B RS in the Standard solution (%)

In Dissolution 〈711〉/Test 8/Tolerances: Change
The percentage of the labeled amount of valproic acid (C₈H₁₆O₂) dissolved at the times specified conform to Dissolution <711>, Acceptance Table 1.
to:
The percentage of the labeled amount of valproic acid (C₈H₁₆O₂) dissolved at the times specified conform to Dissolution <711>, Acceptance Table 2.

Change
Where the label states that Seco barbital Sodium is sterile, it meets the requirements for Sterility Tests 〈71〉 and for Bacterial endotoxins under Secobarbital Sodium for Injection. Where the label states that Secobarbital Sodium must be subjected to further processing during the preparation of injectable dosage forms, it meets the requirements for Bacterial endotoxins under Secobarbital Sodium for Injection.
to:
Where the label states that Secobarbital Sodium is sterile, it meets the requirements for Sterility Tests 〈71〉 and the level of bacterial endotoxins is not more than 0.9 USP Endotoxin Units per mg of secobarbital sodium tested per Bacterial Endotoxins Test <85>. Where the label states that Secobarbital Sodium must be subjected to further processing during the preparation of injectable dosage forms, the level of bacterial endotoxins is not more than 0.9 USP Endotoxin Units per mg of secobarbital sodium tested per Bacterial Endotoxins Test <85>.

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide, monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

Change
System suitability solution: 5 µg/mL each of USP Promethazine Hydrochloride RS and USP Promethazine Related Compound B RS from the Standard stock solution and System suitability stock solution, respectively
Standard solution: 5 µg/mL of USP Promethazine Hydrochloride RS from the Standard stock solution
Sensitivity solution: 0.25 µg/mL of USP Promethazine Hydrochloride RS from the Standard solution
to:
System suitability solution: 5 µg/mL each of USP Promethazine Hydrochloride RS and USP Promethazine Related Compound B RS from the Standard stock solution and System suitability stock solution, respectively, in Diluent
Standard solution: 5 µg/mL of USP Promethazine Hydrochloride RS from the Standard stock solution in Diluent
Sensitivity solution: 0.25 µg/mL of USP Promethazine Hydrochloride RS from the Standard solution in Diluent

Change
Buffer, Mobile phase, System suitability solution, Standard solution, Sample solution, and Chromatographic system: Proceed as directed in the Assay.
to:
Buffer, Mobile phase, System suitability solution, Standard solution, Sample solution, and Chromatographic system: Proceed as directed in the Assay, and use 40 µL injection volume for the Sensitivity solution.

In USP Metaraminol Enantiomer RS: Change
3-[(1S,2R)-2-Amino-1-hydroxypropyl]phenol.
C₉H₁₃NO₂ 167.21
to:
3-[(1S,2R)-2-Amino-1-hydroxypropyl]phenol D-tartrate.
C₉H₁₃NO₂ ∙ C₄H₆O₆ 317.29

In Chromatographic system/Column: Change
4-mm × 30-cm; packing L1
to:
3.9-mm × 30-cm; packing L1
AND
In System suitability: Change
[Note—The relative retention times for bupivacaine hydrochloride and dibutyl phthalate are about 1.0 and 1.2, respectively.]
to:
[Note—The relative retention times for bupivacaine and dibutyl phthalate are about 1.0 and 1.2, respectively.]
AND
In System suitability/Suitability requirements: Change
Resolution: NLT 2.0 between bupivacaine hydrochloride and dibutyl phthalate
Relative standard deviation: NMT 1.0% for the ratio of bupivacaine to the internal standard from three replicate injections
to:
Resolution: NLT 2.0 between bupivacaine and dibutyl phthalate
Relative standard deviation: NMT 1.0% for the peak response ratio of bupivacaine to the internal standard from three replicate injections

In Organic Impurities/System suitability: Change
Sample: Standard solution
[Note—The relative retention times for methoxy tamsulosin, tamsulosin, ethoxyphenoxy ethyl bromide, and desethoxy tamsulosin are 0.73, 1.00, 1.80, and 2.80, respectively.]
Suitability requirements
Tailing factor: NMT 2.0
Relative standard deviation: NMT 5.0%
Signal-to-noise ratio: NLT 10
to:
Samples: Standard solution and Sensitivity solution
[Note—The relative retention times for methoxy tamsulosin, tamsulosin, ethoxyphenoxy ethyl bromide, and desethoxy tamsulosin are 0.73, 1.00, 1.80, and 2.80, respectively.]
Suitability requirements
Tailing factor: NMT 2.0, Standard solution
Relative standard deviation: NMT 5.0%, Standard solution
Signal-to-noise ratio: NLT 10, Sensitivity solution

Change
Shake a portion of Oral Suspension with a mixture of acetone and 0.1 N hydrochloric acid (4:1) to obtain a solution containing about 1 mg of amoxicillin per mL. The solution responds to the Identification test under Amoxicillin Capsules.
to:
Prepare a test solution by shaking a portion of Oral Suspension with a mixture of acetone and 0.1 N hydrochloric acid (4:1) to obtain a solution containing about 1 mg of amoxicillin per mL. Prepare a Standard solution of USP Amoxicillin RS in 0.1 N hydrochloric acid containing 1 mg per mL. Use within 10 minutes after preparation. Apply separately 5 µL of each solution on a thin-layer chromatographic plate coated with a 0.25-mm layer of chromatographic silica gel mixture (see Chromatography 〈621〉). Place the plate in a suitable chromatographic chamber, and develop the chromatogram in a solvent system consisting of a mixture of methanol, chloroform, water, and pyridine (90:80:30:10). When the solvent front has moved about three-fourths of the length of the plate, remove the plate from the chamber, and dry with warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes: the R_F value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide, monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

In Standardization with visual end point: Change
M = mL edetate disodium × edetate disodium/mL ZnSO₄
to:
M = mL edetate disodium × M edetate disodium/mL ZnSO₄
AND
In Standardization with potentiometric end point: Change
M = mL edetate disodium × edetate disodium/mL ZnSO₄
to:
M = mL edetate disodium × M edetate disodium/mL ZnSO₄

In Solution A: Change
0.15 N hydrochloric acid in water prepared as follows. Transfer 150 mL of hydrochloric acid to a 500-mL volumetric flask, dilute with water to volume, and mix well.
to:
0.15 N hydrochloric acid in water prepared as follows. Transfer 150 mL of 0.5 N hydrochloric acid to a 500-mL volumetric flask, dilute with water to volume, and mix well.

In Standard stock solution: Change
1 mg/mL of USP Pindolol RS in Mobile phase prepared as follows. To a suitable amount of USP Pindolol RS add Mobile phase to fill about 90% of the total volume, and sonicate for about 5 min to dissolve.
to:
1 mg/mL of USP Pindolol RS in Mobile phase prepared as follows. To a suitable amount of USP Pindolol RS add Mobile phase to fill about 90% of the total volume, and sonicate for about 5 min to dissolve. Dilute with Mobile phase to volume.

Change
7-Chloro-4-(dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,6,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide monohydrochloride
to:
(4S,4aS,5aS,6S,12aS)-7-Chloro-4-(dimethylamino)-3,6,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-1,4,4a,5,5a,6,11,12a-octahydrotetracene-2-carboxamide monohydrochloride

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide, monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

Change
Standard solution: 1.0 µg/mL of USP p-Chloroaniline RS in Diluent
to:
Standard solution: 0.001 mg/mL of USP p-Chloroaniline RS in Diluent
AND
In Analysis: Change
Result = (r_U/r_S) × (C_S/C_U) × D × 100
to:
Result = (r_U/r_S) × (C_S/C_U) × 100
AND
Delete
D = dilution factor for the Sample solution, 2.5

In Analysis: Change
Result = (r_U/r_S) × (C_S/C_U) × (M_r1/M_r22) × 100
to:
Result = (r_U/r_S) × (C_S/C_U) × (M_r1/M_r2) × 100

Change:
B. Test for Hydroxyl Group:
to:
B. Hydroxyl Value:
AND
In D./Analysis: Change
Dissolve or disperse the Sample in alcohol.
to:
Dissolve or disperse the Sample in 5 mL alcohol.

In Sterility Tests 〈71〉: Change
Where the label states that Piperacillin is sterile or that it must be subjected to further processing during the preparation of injectable dosage forms, it meets the requirements when tested as directed in Test for Sterility of the Product to Be Examined, Membrane Filtration.
to:
Where the label states that Piperacillin is sterile, it meets the requirements when tested as directed in Test for Sterility of the Product to Be Examined, Membrane Filtration.

In Procedure/Analysis: Change
Calculate the percentage of methylbenzethonium chloride (C₂₈H₄₄ClNO₂ · H₂O) in the portion of Methylbenzethonium Chloride taken:
to:
Calculate the percentage of methylbenzethonium chloride (C₂₈H₄₄ClNO₂) in the portion of Methylbenzethonium Chloride taken:

In B. Identification Tests—General 〈191〉, Chemical Identification Tests, Chloride: Change
Meets the requirements when tested as specified in test B.
to:
Meets the requirements of the test for amine hydrochlorides

In USP Doxycycline Related Compound A RS: Change
444.43
to:
444.44
AND
Change
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide, monohydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.13
to:
(4S,4aR,5S,5aR,6S,12aS)-4-(Dimethylamino)-1,4,4a,5,5a,6,11,12a-octahydro-3,5,10,12,12a-pentahydroxy-6-methyl-1,11-dioxo-2-naphthacenecarboxamide hydrochloride.
C₂₂H₂₄N₂O₈ · HCl 480.90

In Analysis: Change
Calculate the percentage of any unspecified impurities in the portion of Sotalol Hydrochloride taken:
Result = (r_U/r_S) × (C_S/C_U) × 100
r_U= sum of all the peak responses of all unspecified impurities from the Sample solution
to:
Calculate the percentage of any unspecified impurity in the portion of Sotalol Hydrochloride taken:
Result = (r_U/r_S) × (C_S/C_U) × 100
r_U = peak response of each unspecified impurity from the Sample solution
AND
In Table 1: Change
Any unspecified impurities
to:
Any unspecified impurity