Errata - English

Change
523.32
to:
523.33
AND
Change
(3R)-3-Amino-1-[3-(trifluoromethyl)-5,6-dihydro[1,2,4]triazolo[4,3-a]pyrazin-7(8H)-yl-4-(2,4,5-trifluorophenyl)butan-1-one phosphate monohydrate
to:
(3R)-3-Amino-1-[3-(trifluoromethyl)-5,6-dihydro[1,2,4]triazolo[4,3-a]pyrazin-7(8H)-yl]-4-(2,4,5-trifluorophenyl)butan-1-one phosphate monohydrate

In Test 2/Analysis: Change
C_S = concentration of USP Prazosin Hydrochloride RS in the Standard solution (µg/mL)
to:
C_S = concentration of USP Prazosin Hydrochloride RS in the Standard solution (mg/mL)
AND
Change
M_r2 = molecular weight of prazosin hydrochloride, 419.86
to:
M_r2 = molecular weight of prazosin hydrochloride, 419.87

In Leachable Arsenic/Analysis: Change
A 3.0-mL portion of the Sample solution meets the requirements in Arsenic 〈211〉, Procedures, Procedure.
to:
A 3.0-mL portion of the Sample solution meets the requirements in Arsenic 〈211〉, Procedures, Procedure 1.

In Acetic Acid in Peptides/Analysis: Change
C_SPA = concentration of potassium acetate in each of the Standard solutions (mg/mL)
to:
C_SPA = concentration of potassium acetate in each of the Standard solutions (µg/mL)
AND
In Ammonium/Analysis: Change
C_SAC = concentration of ammonium chloride in each of the Standard solutions (mg/mL)
to:
C_SAC = concentration of ammonium chloride in each of the Standard solutions (µg/mL)

Change
Uniformity of Dosage Units 〈905〉
Procedure for content uniformity
to:
Uniformity of Dosage Units 〈905〉: Meets the requirements
Procedure for content uniformity, chewable tablets only
AND
In Uniformity of Dosage Units: Delete
Acceptance criteria: Meet the requirements for chewable tablets

In Dissolution 〈711〉/Test 1/Analysis: Change
Determine the percentage of telmisartan (C₃₃H₃₀N₄O₂) dissolved:
Result = (A_U × C_S × V × 100)/(A_S × D × L)
to:
Calculate the percentage of the labeled amount of telmisartan (C₃₃H₃₀N₄O₂) dissolved:
Result = (A_U/A_S) × C_S × V × D × (1/L) × 100
AND
Change
C_S = concentration of the Standard solution (mg/mL)
to:
C_S = concentration of USP Telmisartan RS in the Standard solution (mg/mL)
AND
In Dissolution 〈711〉/Test 2/Analysis: Change
r_U = peak response from the Sample solution
r_S = peak response from the Standard solution
to:
r_U = peak response of telmisartan from the Sample solution
r_S = peak response of telmisartan from the Standard solution
AND
In Dissolution 〈711〉/Test 3/Analysis: Change
C_S = concentration of the Standard solution (mg/mL)
to:
C_S = concentration of USP Telmisartan RS in the Standard solution (mg/mL)

In System suitability: Change
[Note—The approximate relative retention times for (3S,3′S)-zeaxanthin, (3R,3′S-meso)-zeaxanthin, (3R,3′R)-zeaxanthin, and (3R,3′R,6′R)-lutein are 0.94, 1.00, 1.06, and 1.11, respectively.]
to:
[Note—The approximate relative retention times for (3S,3′S)-zeaxanthin, (3R,3′S)-zeaxanthin, (3R,3′R)-zeaxanthin, and (3R,3′R,6′R)-lutein are 0.94, 1.00, 1.06, and 1.11, respectively.]
AND
In System suitability/Suitability requirements/Resolution: Change
(3R,3′S-meso)-zeaxanthin
to:
(3R,3′S)-zeaxanthin
AND
In Analysis: Change
(3R,3′S-meso)-zeaxanthin
to:
(3R,3′S)-zeaxanthin
AND
In Acceptance criteria: Change
(3R,3′S-meso)-Zeaxanthin
to:
(3R,3′S)-Zeaxanthin

In Analysis: Change
M_r1 = molecular weight of atorvastatin, 558.64
M_r2 = molecular weight of atorvastatin calcium, 1155.34
to:
M_r1 = molecular weight of atorvastatin, 558.65
M_r2 = molecular weight of atorvastatin calcium, 1155.36

In Dissolution 〈711〉/Medium: Change
26.7 g/L of sodium acetate trihydrate in water. Add 133 mL of glacial acetic acid to this solution, and then dilute with water to 10 L; 900 mL.
to:
0.02 M sodium acetate buffer, pH 3.5, prepared as follows. Dissolve 2.67 g of sodium acetate in 100 mL of water. Add 13.3 mL of glacial acetic acid and then dilute with water to 1000 mL; 900 mL.

In USP Reference Standards 〈11〉: Change
USP Rivastigmine Tartrate R-Isomer RS
to:
USP Rivastigmine Tartrate R-Isomer RS
(R)-3-[1-(Dimethylamino)ethyl]phenyl ethylmethylcarbamate, hydrogen tartrate.
C₁₄H₂₂N₂O₂ · C₄H₆O₆ 400.42

In Light-resistant container: Change
〈661.2〉, Functionality, Spectral Transmission Requirements for Light-Resistant Components and Systems.
to:
〈661.2〉, Functionality Test Method, Spectral Transmission Requirements for Light-Resistant Components and Systems.

In Limit of Naloxone Related Compound D: Delete
Sensitivity solution: 1.25 µg/mL of USP Naloxone Related Compound D RS in 0.1 N hydrochloric acid
AND
In System suitability/Samples: Delete
Sensitivity solution,
AND
In System suitability/Suitability requirements: Delete
Signal-to-noise ratio: NLT 10, Sensitivity solution

In Analysis: Change
Result = (r_U/r_S) × C_S × (1/F)
to:
Result = (r_U/r_S) × C_F × (1/F)
AND
Change
C_S = final concentration of USP Isoflurane Related Compound B RS in the Standard solution (%)
to:
C_F = final concentration of USP Isoflurane Related Compound B RS in the Standard solution (%)

In Dissolution 〈711〉/Test 8/Tolerances: Change
The percentage of the labeled amount of valproic acid (C₈H₁₆O₂) dissolved at the times specified conform to Dissolution <711>, Acceptance Table 1.
to:
The percentage of the labeled amount of valproic acid (C₈H₁₆O₂) dissolved at the times specified conform to Dissolution <711>, Acceptance Table 2.

Change
Where the label states that Seco barbital Sodium is sterile, it meets the requirements for Sterility Tests 〈71〉 and for Bacterial endotoxins under Secobarbital Sodium for Injection. Where the label states that Secobarbital Sodium must be subjected to further processing during the preparation of injectable dosage forms, it meets the requirements for Bacterial endotoxins under Secobarbital Sodium for Injection.
to:
Where the label states that Secobarbital Sodium is sterile, it meets the requirements for Sterility Tests 〈71〉 and the level of bacterial endotoxins is not more than 0.9 USP Endotoxin Units per mg of secobarbital sodium tested per Bacterial Endotoxins Test <85>. Where the label states that Secobarbital Sodium must be subjected to further processing during the preparation of injectable dosage forms, the level of bacterial endotoxins is not more than 0.9 USP Endotoxin Units per mg of secobarbital sodium tested per Bacterial Endotoxins Test <85>.

In System suitability: Change
Samples: System suitability solution, Standard solution A, and Standard solution B
to:
Samples: System suitability solution and Standard solution A
AND
In Analysis: Change
Samples: Mobile phase, Standard solution A, and Sample solution
Chromatograph the Standard solution and adjust the integration parameters so that the response is 5%–15% of full-scale deflection.
to:
Samples: Mobile phase, Standard solution A, Standard solution B, and Sample solution
Chromatograph Standard solution B and adjust the integration parameters so that the response is 5%–15% of full-scale deflection.

In Test 1: Change
Buffer stage
Medium: 0.05 M pH 6.8 phosphate buffer (see Reagents, Indicators, and Solutions—Buffer Solutions)
to:
Buffer stage
Medium: 0.05 M pH 6.8 phosphate buffer (see Reagents, Indicators, and Solutions—Buffer Solutions); 900 mL

In System suitability/Suitability requirements/Relative standard deviation: Change
NMT 10.0% for the tributyl phosphine oxide and osteltamivir phosphate peaks
to:
NMT 10.0% for the tributyl phosphine oxide and oseltamivir phosphate peaks

In Chromatographic system and Procedure: Change
C is the concentration, in mg per mL, of USP Dextromethorphan Hydrobromide RS, on the anhydrous basis, in the Standard preparation;
to:
C is the concentration, in mg per mL, of USP Dextromethorphan Hydrobromide RS in the Standard preparation;

In Test 1, Test 3, Test 4, Test 5, and Test 6/Analysis: Change
M_r1 = molecular weight of atorvastatin, 558.64
M_r2 = molecular weight of atorvastatin calcium, 1155.34
to:
M_r1 = molecular weight of atorvastatin, 558.65
M_r2 = molecular weight of atorvastatin calcium, 1155.36

In Dissolution 〈711〉/Test 2/Acid stage: Change
Acid stage standard solution: (L/10) mg/mL of USP Pantoprazole Sodium RS from the Standard stock solution in Acid stage medium, where L is the label claim in mg/Tablet
to:
Acid stage standard solution: (L/10000) mg/mL of USP Pantoprazole Sodium RS from the Standard stock solution in Acid stage medium, where L is the label claim in mg/Tablet
AND
In Dissolution <711>/Test 2/Buffer stage: Change
Buffer stage standard solution: (L/1000) of USP Pantoprazole Sodium RS where L is the label claim in mg/Tablet
to:
Buffer stage standard solution: (L/1000) mg/mL of USP Pantoprazole Sodium RS from the Standard stock solution in Buffer stage medium, where L is the label claim in mg/Tablet