Errata - English

In Standardization with visual end point: Change
M = mL edetate disodium × edetate disodium/mL ZnSO₄
to:
M = mL edetate disodium × M edetate disodium/mL ZnSO₄
AND
In Standardization with potentiometric end point: Change
M = mL edetate disodium × edetate disodium/mL ZnSO₄
to:
M = mL edetate disodium × M edetate disodium/mL ZnSO₄

In footnote 1 in Molecular Weight Measurements of Low Molecular Weight Heparins by Gel Permeation Chromatography/Chromatographic system/Columns/Analytical: Change
guard column TSK SWXL 6-mm × 4-mm;
to:
guard column TSK SWXL 6-mm × 4-cm;

In Analysis: Change
Add to the acid solution 5.0 mL of Standard dithizone solution and 4 mL of Ammonia cyanide solution,
to:
Add to the acid solution 5.0 mL of Standard dithizone solution and 4 mL of Ammonium cyanide solution,

In Release Liner Peel Test: Change
The product fails the test if the mean peel force is outside the acceptable range determined during product development.
to:
The product fails the test if the overall mean peel force is outside the acceptable range determined during product development.

In General Pharmacopeial Requirements/Pesticide Residues: Change
where L is the limit in the original article as listed in Table 4 (see Pesticide Residue Analysis under Articles of Botanical Origin <561>)
to:
where L is the limit in the original article as listed in Table 5 (see Pesticide Residue Analysis under Articles of Botanical Origin <561>)

In Liquid Chromatography: Isocratic Elution/Injection volume: Change
Result = (V_inj2 = V_inj1 (L₂ d_c2² )/(L₁ d_c1²)
to:
V_inj2 = V_inj1 (L₂ d_c2² )/(L₁ d_c1²)
AND
In Liquid Chromatography: Gradient Elution/Column parameters and flow rate: Change
F₂ = F₂ × [(dc₂² × dp₁)/(dc₁² × dp₂)]
to:
F₂ = F₁ × [(dc₂² × dp₁)/(dc₁² × dp₂)]

In Liquid Chromatography: Isocratic Elution/Injection volume: Change
L₂ = internal diameter of the column used (mm)
dc₁ = particle size indicated in the monograph (µm)
dc₂ = particle size of the column used (µm)
to:
L₂ = new column length (mm)
dc₁ = column internal diameter indicated in the monograph (mm)
dc₂ = new column internal diameter (mm)

In Light-resistant container: Change
〈661.2〉, Functionality, Spectral Transmission Requirements for Light-Resistant Components and Systems.
to:
〈661.2〉, Functionality Test Method, Spectral Transmission Requirements for Light-Resistant Components and Systems.

Change
The spectrum obtained from the Sample solution shows IR maxima in the regions of 3500–3200, 2950–2890, 1653–1633, and 1070–1000 cm^–1.
to:
The spectrum obtained from the sample preparation shows IR maxima in the regions of 3500–3200, 2950–2890, 1653–1633, and 1070–1000 cm^–1.

In A.: Change
Spectroscopic Identification Tests 〈197〉, Infrared Spectroscopy: 197A, 197K, and 197S
to:
Spectroscopic Identification Tests 〈197〉, Infrared Spectroscopy: 197A, 197K, or 197S
Procedure for 197S

In Analysis: Change
M_W(Salt) = molecular weight of ammonium glycyrrhizate, 840.08 g/mol
M_W(Acid) = molecular weight of glycyrrhizic acid, 821.59 g/mol
to:
M_W(Salt) = molecular weight of ammonium glycyrrhizate, 839.97 g/mol
M_W(Acid) = molecular weight of glycyrrhizic acid, 822.94 g/mol

Change
Application volume, Developing solvent system, Procedure—Proceed as directed for the Identification test under Amoxicillin Tablets.
to:
Application volume—5 µL.
Developing solvent system—a mixture of methanol, chloroform, water, and pyridine (90:80:30:10).
Procedure—Proceed as directed in Thin-Layer Chromatographic Identification Test <201>. Dry the plate with the aid of a current of warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes.

Change
Prepare a test solution containing the equivalent of 4 mg of amoxicillin per mL by adding 0.1 N hydrochloric acid to Amoxicillin for Injectable Suspension. Allow the solution to stand for 5 minutes before use: the solution responds to the Identification test under Amoxicillin Capsules.
to:
Prepare a test solution containing the equivalent of 4 mg of amoxicillin per mL by adding 0.1 N hydrochloric acid to Amoxicillin for Injectable Suspension. Allow the solution to stand for 5 minutes before use. Prepare a Standard solution of USP Amoxicillin RS in 0.1 N hydrochloric acid containing 4 mg per mL. Use within 10 minutes after preparation. Apply separately 5 µL of each solution on a thin-layer chromatographic plate coated with a 0.25-mm layer of chromatographic silica gel mixture (see Chromatography <621>). Place the plate in a suitable chromatographic chamber, and develop the chromatogram in a solvent system consisting of a mixture of methanol, chloroform, water, and pyridine (90:80:30:10). When the solvent front has moved about three-fourths of the length of the plate, remove the plate from the chamber, and dry with warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes: the R_F value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.

Change
The solution obtained responds to the Identification test under Amoxicillin Capsules.
to:
Prepare a Standard solution of USP Amoxicillin RS in 0.1 N hydrochloric acid containing 4 mg per mL. Use within 10 minutes after preparation. Apply separately 5 µL of each solution on a thin-layer chromatographic plate coated with a 0.25-mm layer of chromatographic silica gel mixture (see Chromatography <621>). Place the plate in a suitable chromatographic chamber, and develop the chromatogram in a solvent system consisting of a mixture of methanol, chloroform, water, and pyridine (90:80:30:10). When the solvent front has moved about three-fourths of the length of the plate, remove the plate from the chamber, and dry with warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes: the R_F value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.

Change
Shake a portion of Oral Suspension with a mixture of acetone and 0.1 N hydrochloric acid (4:1) to obtain a solution containing about 1 mg of amoxicillin per mL. The solution responds to the Identification test under Amoxicillin Capsules.
to:
Prepare a test solution by shaking a portion of Oral Suspension with a mixture of acetone and 0.1 N hydrochloric acid (4:1) to obtain a solution containing about 1 mg of amoxicillin per mL. Prepare a Standard solution of USP Amoxicillin RS in 0.1 N hydrochloric acid containing 1 mg per mL. Use within 10 minutes after preparation. Apply separately 5 µL of each solution on a thin-layer chromatographic plate coated with a 0.25-mm layer of chromatographic silica gel mixture (see Chromatography 〈621〉). Place the plate in a suitable chromatographic chamber, and develop the chromatogram in a solvent system consisting of a mixture of methanol, chloroform, water, and pyridine (90:80:30:10). When the solvent front has moved about three-fourths of the length of the plate, remove the plate from the chamber, and dry with warm air for 10 minutes. Locate the spots on the plate by spraying lightly with a solution of ninhydrin in alcohol containing 3 mg per mL, and dry at 110° for 15 minutes: the R_F value of the principal spot obtained from the test solution corresponds to that obtained from the Standard solution.

In Dissolution <711>/Test 1/Procedure/Chromatographic procedure/Analysis: Change
Result = (R_U/R_S) × C_S × V × (1/L) × 100
to:
Result = (R_U/R_S) × C_S × V × D × (1/L) × 100
AND
Add
D = dilution factor of the Sample solution, 2

Change
USP Atorvastatin Related Compound H RS (lactone impurity)
to:
USP Atorvastatin Related Compound H RS
Also known as Lactone impurity;
AND
Change
USP Atorvastatin Related Compound I RS (acetonide impurity)
to:
USP Atorvastatin Related Compound I RS
Also known as Acetonide impurity;

In Analysis: Change
M_r1 = molecular weight of atorvastatin, 558.64
M_r2 = molecular weight of atorvastatin calcium, 1155.34
to:
M_r1 = molecular weight of atorvastatin, 558.65
M_r2 = molecular weight of atorvastatin calcium, 1155.36

In Analysis: Change
M_r1 = molecular weight of atorvastatin, 558.64
M_r2 = molecular weight of atorvastatin calcium, 1155.34
to:
M_r1 = molecular weight of atorvastatin, 558.65
M_r2 = molecular weight of atorvastatin calcium, 1155.36

In Test 1, Test 3, Test 4, Test 5, and Test 6/Analysis: Change
M_r1 = molecular weight of atorvastatin, 558.64
M_r2 = molecular weight of atorvastatin calcium, 1155.34
to:
M_r1 = molecular weight of atorvastatin, 558.65
M_r2 = molecular weight of atorvastatin calcium, 1155.36

Change
Related Compounds
System suitability solution and Sample solution: Prepare as directed in the Assay.
Analysis
Samples: System suitability solution and Sample solution
Using the chromatograms of the Sample solution and the System suitability solution, calculate the percentage of atovaquone related compounds in the portion of Atovaquone taken:
to:
Organic Impurities
Mobile phase, Diluent, System suitability solution, Standard solution, Sample solution, Chromatographic system and System suitability: Proceed as directed in the Assay.
Analysis
Sample: Sample solution
Calculate the percentage of atovaquone related compounds in the portion of Atovaquone taken:

Change
2-(2-Carboxyethyl)-1,2,3,4-tetrahydro-6,7-dimeth oxy-2-methyl-1-veratrylisoquinolinium benzenesulfonate, pentamethylene ester
to:
2-(2-Carboxyethyl)-1,2,3,4-tetrahydro-6,7-dimethoxy-2-methyl-1-veratrylisoquinolinium benzenesulfonate, pentamethylene ester

In Organic Impurities/Table 2: Change
3'-N-Demethyl-3'-N-[(4-methylphenyl)sulfonyl]azithromycin^m
to:
3′-N-{[4-(Acetylamino)phenyl]sulfonyl}-3′-demethylazithromycin^m
AND
In Table 2/footnote m: Change
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-methylphenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-ß-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.
to:
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-acetamidophenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-β-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.

In Organic Impurities/Table 2: Change:
3′-N-{[4-(Acetylamino)phenyl]sulfonyl}-3′-demethylazithromycin^m
to:
3’-N-Demethyl-3’-N-[(4-methylphenyl)sulfonyl]azithromycin^m
AND
In Organic Impurities/Table 2/footnote m: Change
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-acetamidophenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-β-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.
to:
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-methylphenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-ß-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.

In footnote m in Table 2: Change
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-acetamidophenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-β-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.
to:
(2R,3S,4R,5R,8R,10R,11R,12S,13S,14R)-13-[(2,6-Dideoxy-3-C-methyl-3-O-methyl-α-L-ribo-hexopyranosyl)oxy]-2-ethyl-3,4,10-trihydroxy-3,5,6,8,10,12,14-heptamethyl-11-[[3-[N-(4-methylphenylsulfonyl)-N-methylamino]-3,4,6-trideoxy-ß-D-xylo-hexopyranosyl]oxy]-1-oxa-6-azacyclopentadecan-15-one.

In USP Reference Standards 〈11〉/USP Azaerythromycin A RS: Change
734.96
to:
734.97
AND
In USP Azithromycin N-oxide RS: Change
764.98
to:
765.00
AND
In USP N-Demethylazithromycin RS: Change
734.96
to:
734.97
AND
In USP Desosaminylazithromycin RS: Change
590.79
to:
590.80